The Blank Plates Mount have four threaded 8-32 (M4) holes so you can mount that unusual optic. Use the mounts horizontally as a low cost tip-tilt stage or vertically as a more traditional optic mount.

New Focus

Blank Plates

Ideal for laboratory use as well as for building into your products, these versions ship with two adjustments screws, extra-stiff springs for better long-term stability and actuators.

New Focus

Commercial Mounts

- More stable and economical than traditional magnetic bases
- Low beam height - as low as 1.5"
- The fixed-height pedestal risers can make the difference between a stable setup and one that suffers from vibrations.

Magnetic Pedestal Base

• Model 9904 The convenience of a magnetic base with the same stability and low beam height of pedestal risesr. Suitable for applications where tight space means you can"t use a holding fork.

Post-Holder Pedestal Base

• Model 9910 If you want the flexibility of an adjustable-height post system, but like the versatility of the forks, use this base with your post holders.

Pedestal Clamp

• Model 9141 The pedestal clamps let you vary the height of your optical mounts without having to give up the stability of the pedestal risers.

1/4-20 Pedestal

• Model 9959 These pedestals have a 1/4-20 thread tapped hole on the top and an 8-32 tapped hole on the bottom.

Pedestal Shim Set

• Model 9950 The shim set includes a 1/4" and 1/8" pedestal shims that let you reach those in-between heights while retaining all the stability of the fixed-height mounting scheme.

New Focus

Fixed Pedestal System

The Flipper™ mounts were created by adding a hinge to a traditional optic mount. The result is a mount that lets you move an optic into and out of your beam path easily and repeatably.

• Easily flips optics into and out of your beam path
  
• Kinematic design gives youu 200 µrad repeatability
  
• Lockable

New Focus

Flipper Mounts

The performance of more expensive gimbal mounts at a fraction of the cost.

New Focus Gimbal Mounts offer more stability and higher resolution than traditional non-kinematic gimbal mounts.

• Pure tilt without translation
  
• Pivot is centered on the optic not the frame
  
• Extra stiff for high stability
  

The rotation point in these mounts is in line with the center of the mirror giving you pure tilt with the turn of just one screw.

New Focus

Gimbal Mounts

- Nudgers for precise relocation of mounts
- High resolution micrometers
- Starrett micrometers compatible with the Triple - Divide translation stages

Nudgers

• Model 9315 Finely position your set-up with this ball-tipped pusher, or use it for precise relocation of your components

High Resolution Micrometers

• Model 9351 The high resolution calibrated micrometer style adjustments screws have 1/4-100 threads to give you finer resolution than conventional micrometers (typically 40-pitch threads).

Micrometers

• Models 9352 and 9353 These high quality Starrett® micrometers are clearly marked for 0.01 mm accuracy and are ideal for use with the Triple Divide™ translation stages.

New Focus

Micrometers & Nudgers

With the unique Opti-Claw™ you won"t have to adjust the height of the mount everytime you want to use a different diameter optic.
This clever mount automatically centers any optic with a diameter from 0.10"(2.5mm) to 2.0"(51mm) to within 0.005"

• Ideal for swapping and re-centering optics quickly
  
• Great for holding lenses and beamsplitters
  
• Locking screw offers the secure hold of a fixed diameter mount

New Focus

Opti-Claws

New Focus

Pint-Sized Mounts

New Focus patented Prism/Beamsplitter Mounts offer three orthogonal axes of rotation. Designed for intuitive alignment, the rotation point is located under the center of the mounting plate so that you get minimal translation during adjustments.

• Full range of motion in all three axes available simultaneously
  
• Press-fit holder means no need for sticky tape Intuitive and affordable

New Focus

Prism Mounts

- Ultrastable
- Unique optic-retention system for minimising distortion of the optics
- Ultraclean versions are vacuum-compatible to 10&masr;6 Torr.

Stability™ Top and Centre Mounts Models 9814, 9816 and 9817 These special Stability Top (Model 9814) and Centre Mounts (Models 9816 and 9817) build upon the New Focus tradition of manufacturing outstanding kinematic mounts that use the best adjustment screws and sapphire seats. With the new unique retention system, these mounts provide further performance enhancements. Designed originally for precision UV beam-steering applications in the demanding UV semiconductor capital-equipment industry, the new retention system optimises stability while minimising wavefront distortion, ensuring that the mirrors are truly flat and rock solid. Mirror installation and removal is simple and fast, requiring no adhesives. The top actuated version in which all adjustments are accessed along the top is ideal for use in compact spaces where access is limited.

New Focus

Stability Top & Centre Mounts

These mirror mounts are ideal for use in compact spaces. They give you easy access to both tip and tilt adjustments from the top without worrying about blocking the beam.

• Top and side mounting options
  
• Low cost
  
• Locakable design

New Focus

Top-Actuated Mounts

- Same proprietary 1/4-80 screw sets found in the classic line
- Ideal for beam-steering and pointing applications
- Versatile compact mount holds 1" and ½" optics.

Center Valu-Mounts

• Model 9773 To achieve a high level of stability, New Focus uses a ½" frame that is stiffer than any you"ll find on other comparably priced mounts.

Tiny Corner Valu-Mounts

• Model 9761-K These tiny corner mounts are made from aluminium rather than staineless steel to save you money as well as space.

Compact Valu-Mounts

• Model 9771 Ideal for applications where space is tight.

New Focus

Valu-Mounts